MeanWell 5V 26A 130W Power Supply Source (RS-150-5)

MeanWell 5V 26A 130W power supply source (RS-150-5)

Availability: In stock

$28.00
Details
Details

Product Name:
MeanWell 5V 26A 130W power supply source (RS-150-5)

Case:806 Size:199×98×38mm
Power: 130W
100% full load burn-in test
All using 105℃ long life electrolytic capacitors
LED indicator for power on
Cooling by free aire convection
High operatiing temperature up tp 70℃
High efficiency, Long life and high reliability
Protections: Short circuit / Overload / Over voltage
1 year warranty

Product Specifications :

Model RS-150-5
Input Voltage Range 85~ 264VAC 120~ 370VAC
FREQUENCY RANGE 47 ~ 63Hz
AC CURRENT (Typ.) 3.5A/115VAC 1.5A/230VAC
LEAKAGE CURRENT <2mA / 240VAC
INRUSH CURRENT (Typ.) COLD START 65A/230VAC
EFFICIENCY (Typ.) 83%
Output RATED CURRENT 26A
DC VOLTAGE 5V
RATED POWER 130W
CURRENT RANGE 0-60A
VOLTAGED ADJ. RANGE 4.75~ 5.5V
RIPPLE & NOISE (max.) Note.2 80mVp-p
VOLTAGE TOLERANCE Note.3 ±2.0%
LOAD REGULATION Note.5  ±1.5%
LINE REGULATION Note.4  ±0.5%
HOLD UP TIME 20ms at full load
SETUP, RISE TIME 600ms,40ms at full load
Protection OVER VOLTAGE 5.75~ 6.75V
Protection type :Shut off 0/p volltage, clamping by zener diode
OVER LOAD Above 150% rated output power
Protection type :Hiccup mode, recovers automatically after fault condition is removed
Safety WITHSTAND VOLTAGE I/P-O/P:3KVAC I/P-FG:2KVAC O/P-FG:0.5KVAC
SAFETY STANDARDS Note 6 UL60950-1, CB(IEC60950-1),CCC GB4943, 1:2011 approved
ISOLATION RESISTANCE I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25 / 70% RH
EMC STANDARDS EN55022 class B, EN61000-3-2,3, EN61000-4-2,3,4,5,6,8,11, GB9254
Environment  WORKING HUMIDITY  20 ~ 90% RH non-condensing
 WORKING TEMP  -20 ~ +70 (Refer to output load derating curve)
 TEMP. COEFFICIENT  ± 0.03%/℃ (0 ~ 50℃)
 STORAGE TEMP., HUMIDITY  -40 ~ +85 , 10 ~ 95% RH
 VIBRATION  10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes
 Others  DIMENSION  199*98*38mm (L*W*H)
MTBF 1608.8K hrs min. MIL-HDBK-217F (25 ) ℃
Note I. Al parameters NOT specialy mentioned are measured at 230VAC input. rated load and 25℃ of ambient temperature.
2 Ripple & noise are measured at 20MHz Of bandwidth by usig a I2' twisted pair-wire terminated with a 0.1UI & 470 Parallel capacitor
3. Tolerance : includes set up tolerance. line regulation and load regulation.
4. Line regulation is measured from low line to high line at rated load.
5. Load regulation is measured from 0% to 100% rated load.
6. For the request of GEl4943.1.the power soppy is only suable for use in the altitude 2000m below and the non tropical climate condrtion.
7. The power supply is considered a component which will be instated into a final equipment The final equipment must be re-confirmed that
 it still mesh EMC drectives. For guidance on how to perform the EMC tests. please refer to 'EMI testing of component power supplies' 
Tags
Tags

Use spaces to separate tags. Use single quotes (') for phrases.